Plugin name 'sidebar.BROKEN' is not a valid plugin name, only the characters a-z and 0-9 are allowed. Maybe the plugin has been installed in the wrong directory?

e n g i n k o . s u p p o r t . c e n t e r

Trace: › manual_mcf-lw12met › manual_mcf-lw13mio › manual_egk-lw20l00

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
manual_mcf-lw06010 [2022/02/16 09:14] – [2.1Technical data] supportadminmanual_mcf-lw06010 [2025/02/28 12:42] (current) – [11 Declaration of conformity] supportadmin
Line 139: Line 139:
  
  
-enginko provides, upon free registration,  user manuals, javascript examples, downlink generator, uplink decoder, firmware updates and different tools :+Angel4Future provides user manuals, javascript examples, downlink generator, uplink decoder, firmware updates and different tools :
  
  
Line 178: Line 178:
  
 Period is the interval (in minutes) between one measure and the next one. The sensor sends one measures for every transmission. Period is the interval (in minutes) between one measure and the next one. The sensor sends one measures for every transmission.
-Value can be between 15 and 65535 minutes (default: 30 minutes).+Value can be between 5 and 65535 minutes (default: 10 minutes).
  
 Period interval can be set with LoRaWEB or with downlink command.  Period interval can be set with LoRaWEB or with downlink command. 
- 
 ==== 4.2 Thresholds ==== ==== 4.2 Thresholds ====
  
Line 265: Line 264:
 {{ :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400 |}} {{ :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400 |}}
  
-The device exits factory activated with **NONE** mode.+The device exits factory activated with **OTAA ENGINKO** mode.
 On request devices can be shipped aleady activated. On request devices can be shipped aleady activated.
  
Line 309: Line 308:
  
  
-To bring back the sensor to factory default and reset the passwords, a reset code must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code).+To bring back the sensor to factory default and reset the passwords, a reset code must be requested to Angel4Future (please provide the DevEUI of the sensor when you ask for that code).
  
 ===== 8 General configuration file =====  ===== 8 General configuration file =====
  
-WIth LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to enginko). This is very useful especially in +WIth LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to Angel4Future). This is very useful especially in 
 case of multiple devices configuration. case of multiple devices configuration.
  
-With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to enginko's support if needed.+With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to Angel4Future's support if needed.
  
  
Line 341: Line 340:
  
  
-For details on files format please ask to enginko.+For details on files format please ask to Angel4Future.
  
 ===== 9 Payload ===== ===== 9 Payload =====
Line 366: Line 365:
 ===== 11 Declaration of conformity ===== ===== 11 Declaration of conformity =====
  
-Hereby, enginko Srl declares that MCF-LW06010 complies with the essential requirements and other relevant provisions of Directive  2014/53/EU.+Declarations of conformity are available from Angel4Future by sending a request email to sensor@enginko.com..
  
 ===== 12 FCC compliance for MCF-LW06010-US ===== ===== 12 FCC compliance for MCF-LW06010-US =====
Line 385: Line 384:
 ===== 13 Contacts ===== ===== 13 Contacts =====
  
-**enginko Srl** \\  +**Angel4Future S.r.l.** \\  
-Via Roma 3  I-28060 Sozzago (NO) \\  +Via San Sabino 21 - 70042 MOLA DI BARI (BA) , ITALY \\  
-T  :    +39 0321 15 93 088 \\  +T  :    +39 080 532 1796 \\  
  
-E  :    info@enginko.com  \\  +E  :    info@angel4future.com  \\  
-PEC: enginkosrl@legalmail.it \\  +W:     enginko.com \\ \\ 
-W:     enginko.com \\ +
  
 ---- ----
  
-rev.0+rev.1
Last modified: 2023/05/29 07:33