This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| manual_mcf-lw06424 [2022/02/16 07:49] – [3.2 Analog inputs] supportadmin | manual_mcf-lw06424 [2025/02/28 12:39] (current) – [11 Declaration of conformity] supportadmin | ||
|---|---|---|---|
| Line 50: | Line 50: | ||
| * 4 analog current inputs 4-20mA 12bits and disconnect alarm | * 4 analog current inputs 4-20mA 12bits and disconnect alarm | ||
| * 4 programable thresholds for each channel | * 4 programable thresholds for each channel | ||
| - | * Integrated termination and polarization resistors | ||
| * USB On The Go | * USB On The Go | ||
| * IoT node setup ad firmware upgrade via USB interface | * IoT node setup ad firmware upgrade via USB interface | ||
| Line 155: | Line 154: | ||
| - | enginko provides, upon free registration, | + | enginko provides user manuals, javascript examples, downlink generator, uplink decoder, firmware updates and different tools : |
| Line 194: | Line 193: | ||
| Period is the interval (in minutes) between one measure and the next one. The sensor sends one measures for every transmission. | Period is the interval (in minutes) between one measure and the next one. The sensor sends one measures for every transmission. | ||
| - | Value can be between | + | Value can be between |
| Period interval can be set with LoRaWEB or with downlink command. | Period interval can be set with LoRaWEB or with downlink command. | ||
| Line 281: | Line 280: | ||
| {{ : | {{ : | ||
| - | The device exits factory activated with **NONE** mode. | + | The device exits factory activated with **OTAA ENGINKO** mode. |
| - | On request devices can be shipped | + | On request devices can be shipped |
| Note: in **OTAA** AppKey is write only, in reading the field will always be empty, even if set. | Note: in **OTAA** AppKey is write only, in reading the field will always be empty, even if set. | ||
| Line 325: | Line 324: | ||
| - | To bring back the sensor to factory default and reset the passwords, a reset code must be requested to enginko | + | To bring back the sensor to factory default and reset the passwords, a reset code must be requested to Angel4Future |
| ===== 8 General configuration file ===== | ===== 8 General configuration file ===== | ||
| - | WIth LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to enginko). This is very useful especially in | + | WIth LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to Angel4Future). This is very useful especially in |
| case of multiple devices configuration. | case of multiple devices configuration. | ||
| - | With " | + | With " |
| Line 357: | Line 356: | ||
| - | For details on files format please ask to enginko. | + | For details on files format please ask to Angel4Future. |
| ===== 9 Payload ===== | ===== 9 Payload ===== | ||
| Line 382: | Line 381: | ||
| ===== 11 Declaration of conformity ===== | ===== 11 Declaration of conformity ===== | ||
| - | Hereby, enginko Srl declares that MCF-LW06424 complies with the essential requirements and other relevant provisions | + | Declarations |
| ===== 12 FCC compliance for MCF-LW06424-US ===== | ===== 12 FCC compliance for MCF-LW06424-US ===== | ||
| Line 401: | Line 400: | ||
| ===== 13 Contacts ===== | ===== 13 Contacts ===== | ||
| - | **enginko Srl** \\ | + | **Angel4Future S.r.l.** \\ |
| - | Via Roma 3 I-28060 Sozzago | + | Via San Sabino 21 - 70042 MOLA DI BARI (BA) , ITALY \\ |
| - | T : +39 0321 15 93 088 \\ | + | T : +39 080 532 1796 \\ |
| - | E : info@enginko.com | + | E : info@angel4future.com \\ |
| - | PEC: enginkosrl@legalmail.it | + | W: |
| - | W: | + | |
| ---- | ---- | ||
| - | rev.0 | + | rev.1 |