Plugin name 'sidebar.BROKEN' is not a valid plugin name, only the characters a-z and 0-9 are allowed. Maybe the plugin has been installed in the wrong directory?

e n g i n k o . s u p p o r t . c e n t e r

Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
manual_mcf-lw06485 [2024/06/12 16:50] – [4.2.2 Registers map configuration] supportadminmanual_mcf-lw06485 [2025/02/28 12:37] (current) – [12 Declaration of conformity] supportadmin
Line 136: Line 136:
  
  
-enginko provides, upon free registration,  user manuals, javascript examples, downlink generator, uplink decoder, firmware updates and different tools :+Angel4Future provides user manuals, javascript examples, downlink generator, uplink decoder, firmware updates and different tools :
  
  
Line 266: Line 266:
 === 4.2.4 Configuration with LoraWEB (via USB)  === === 4.2.4 Configuration with LoraWEB (via USB)  ===
  
 +To upload the new configuration file (.XLS) select "Save configuration" button:
  
 {{ :wiki:manual_mcf-lw06485:save.jpg?&800 |}} {{ :wiki:manual_mcf-lw06485:save.jpg?&800 |}}
  
-{{ :wiki:manual_mcf-lw06485:upload.jpg?nolink&400 |}}+and then "Upload and Save": 
 + 
 +{{ :wiki:manual_mcf-lw06485:upload.jpg?nolink&600 |}} 
 + 
 +then select the file to be loaded. 
 + 
 +__The file must be closed before this operation__.
  
 === 4.2.5 Configuration with downlinks === === 4.2.5 Configuration with downlinks ===
Line 354: Line 360:
 {{ :wiki:loraweb:loraweb_lora.jpg?direct&600 |}} {{ :wiki:loraweb:loraweb_lora.jpg?direct&600 |}}
  
-The device exits factory activated with **NONE** mode.+The device exits factory activated with **OTAA ENGINKO** mode.
 On request devices can be shipped aleady activated. On request devices can be shipped aleady activated.
  
Line 398: Line 404:
  
  
-To bring back the sensor to factory default and reset the passwords, a reset code must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code).+To bring back the sensor to factory default and reset the passwords, a reset code must be requested to Angel4Future (please provide the DevEUI of the sensor when you ask for that code).
  
 ===== 8 General configuration file =====  ===== 8 General configuration file =====
  
-With LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to enginko). This is very useful especially in +With LoRaWEB is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to Angel4Future). This is very useful especially in 
 case of multiple devices configuration. case of multiple devices configuration.
  
-With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to enginko's support if needed.+With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to Angel4Future's support if needed.
  
  
Line 430: Line 436:
  
  
-For details on files format please ask to enginko.+For details on files format please ask to Angel4Future.
  
 ===== 9 Payload ===== ===== 9 Payload =====
Line 554: Line 560:
 ===== 12 Declaration of conformity ===== ===== 12 Declaration of conformity =====
  
-Hereby, enginko Srl declares that MCF-LW06485 complies with the essential requirements and other relevant provisions of Directive  2014/53/EU.+Declarations of conformity are available from Angel4Future by sending a request email to sensor@enginko.com.
  
 ===== 13 FCC compliance for MCF-LW06485-US ===== ===== 13 FCC compliance for MCF-LW06485-US =====
Line 573: Line 579:
 ===== 14 Contacts ===== ===== 14 Contacts =====
  
-**enginko Srl** \\  +**Angel4Future S.r.l.** \\  
-Via Roma 3  I-28060 Sozzago (NO) \\  +Via San Sabino 21 - 70042 MOLA DI BARI (BA) , ITALY \\  
-T  :    +39 0321 15 93 088 \\  +T  :    +39 080 532 1796 \\  
  
-E  :    info@enginko.com  \\  +E  :    info@angel4future.com  \\  
-PEC: enginkosrl@legalmail.it \\  +W:     enginko.com \\  
-W:     enginko.com \\ +
  
 ---- ----
  
-rev.1+rev.2
Last modified: 2024/06/12 16:50