Plugin name 'sidebar.BROKEN' is not a valid plugin name, only the characters a-z and 0-9 are allowed. Maybe the plugin has been installed in the wrong directory?

e n g i n k o . s u p p o r t . c e n t e r

Trace:

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
manual_egk-lw22ccm [2025/02/28 09:07] – [EGK-LW22CCM Operating Manual] supportadminmanual_egk-lw22ccm [2026/05/20 09:44] (current) – [11 Declaration of conformity] supportadmin
Line 164: Line 164:
 This sensor contains lithium battery, which must be disposed of separately. This sensor contains lithium battery, which must be disposed of separately.
  
-EGK-LW22CCM is provided with two CR123A  batteries.+EGK-LW22CCM is provided with two CR123A batteries.
  
 This is the estimated battery life (in **years**) in the worst conditions: This is the estimated battery life (in **years**) in the worst conditions:
Line 176: Line 176:
   * remove the front panel of the sensor with a small hex key (for M2.5 bolts):   * remove the front panel of the sensor with a small hex key (for M2.5 bolts):
  
-{{ :wiki:manual_egk-lw22ccm:ccm_bolts.jpg?400 |}}+{{  :wiki:manual_egk-lw22ccm:ccm_bolts.jpg?400  }}
  
-  * remove the PCB batteries  from the  board and put the new ones:+  * remove the PCB batteries from the board and put the new ones:
  
-{{ :wiki:manual_egk-lw22ccm:ccm_bat1.jpg?400 |}}+{{  :wiki:manual_egk-lw22ccm:ccm_bat1.jpg?400  }}
  
-{{ :wiki:manual_egk-lw22ccm:ccm_bat2.jpg?400 |}}+{{  :wiki:manual_egk-lw22ccm:ccm_bat2.jpg?400  }}
  
   * Place the front panel and fix it with the 4 bolts.   * Place the front panel and fix it with the 4 bolts.
- 
  
 __After the batteries replacement, internal counters need to be resetted.__ __After the batteries replacement, internal counters need to be resetted.__
Line 191: Line 190:
 {{  :wiki:manual_mcf-lw12terwp:batt_res.jpg?400  |batt_res.jpg}} {{  :wiki:manual_mcf-lw12terwp:batt_res.jpg?400  |batt_res.jpg}}
  
-To perform the operation, you need a unique reset code that must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code):+To perform the operation, you need a unique reset code that must be requested to Angel4Future (please provide the DevEUI of the sensor when you ask for that code):
  
 {{  :wiki:manual_mcf-lw12co2e:battery_res_0.jpg?400  |battery_res_0.jpg}} {{  :wiki:manual_mcf-lw12co2e:battery_res_0.jpg?400  |battery_res_0.jpg}}
  
 At the end of the procedure the battery level displays 100%. At the end of the procedure the battery level displays 100%.
 +
  
 ==== 2.7 Firmware update ==== ==== 2.7 Firmware update ====
Line 282: Line 282:
   - **NONE**: sensor not activated   - **NONE**: sensor not activated
   - **OTAA**: the JoinEUI and the AppKey not setted, must be written to the device;   - **OTAA**: the JoinEUI and the AppKey not setted, must be written to the device;
-  - **OTAA ENGINKO**: Over the air activation, fixed keys: JoinEUI = 904e915000000001, AppKey on request;+  - **OTAA MCF88**: Over the air activation, fixed keys: JoinEUI = 904e915000000001, AppKey on request;
   - **OTAA ENGINKO**: Over the air activation, fixed keys: JoinEUI = 904e915000000001, AppKey on request;   - **OTAA ENGINKO**: Over the air activation, fixed keys: JoinEUI = 904e915000000001, AppKey on request;
   - **ABP**: requires writing to the device of NwkSkey, AppSkey, DevAddr.   - **ABP**: requires writing to the device of NwkSkey, AppSkey, DevAddr.
 {{  :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400  |activation1_0.jpg}} {{  :wiki:manual_mcf-lw12co2e:activation1_0.jpg?400  |activation1_0.jpg}}
  
-The device exits factory activated with **NONE**  mode. On request devices can be shipped aleady activated.+The device exits factory activated with **OTAA ENGINKO** mode. On request devices can be shipped aleady activated.
  
 Note: in **OTAA**  AppKey is write only, in reading the field will always be empty, even if set. Note: in **OTAA**  AppKey is write only, in reading the field will always be empty, even if set.
 +
  
 ==== 4.2 Other settings ==== ==== 4.2 Other settings ====
Line 362: Line 363:
 {{  :wiki:manual_mcf-lw12co2e:password2_0.jpg?400  |password2_0.jpg}} {{  :wiki:manual_mcf-lw12co2e:password2_0.jpg?400  |password2_0.jpg}}
  
-To bring back the sensor to factory default and reset the passwords, a reset code must be requested to enginko (please provide the DevEUI of the sensor when you ask for that code).+To bring back the sensor to factory default and reset the passwords, a reset code must be requested to Angel4Future Srl (please provide the DevEUI of the sensor when you ask for that code). 
  
 ===== 6 Configuration file ===== ===== 6 Configuration file =====
  
-WIth LoRa Tool App is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to enginko). This is very useful especially in case of multiple devices configuration.+WIth LoRa Tool App is possible to configure the device using an XML file, instead to manually adjust the parameters (for details about the file format please ask to Angel4Future). This is very useful especially in case of multiple devices configuration.
  
-With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to enginko's support if needed.+With "Save" button an XML file with the actual configuration of the sensor will be generated. This is useful to store or clone the configuration, or to send it to Angel4Future's support if needed.
  
 {{  :wiki:manual_mcf-lw12co2e:files_rev0.jpg?400  |files_rev0.jpg}} {{  :wiki:manual_mcf-lw12co2e:files_rev0.jpg?400  |files_rev0.jpg}}
Line 395: Line 397:
 {{  :wiki:manual_mcf-lw12co2e:multiple_rev0.jpg?400  |multiple_rev0.jpg}} {{  :wiki:manual_mcf-lw12co2e:multiple_rev0.jpg?400  |multiple_rev0.jpg}}
  
-For details on files format please ask to enginko.+For details on files format please ask to Angel4Future.
  
 ===== 7 LoRaWEB Tool ===== ===== 7 LoRaWEB Tool =====
  
-enginko provides, upon free registration, **LoRaWEB**  online tool, where for each sensor it is possible to find documentation, javascript examples for parsing, downlink generator and uplink decoder:+Angel4Future provides free **LoRaWEB**  online tool, where for each sensor it is possible to find documentation, javascript examples for parsing, downlink generator and uplink decoder:
  
 [[https://iot.ENGINKO.cloud/LoRaWeb/#/configuration|LoRaWEB Tool]] (iot.ENGINKO.cloud/LoRaWeb) [[https://iot.ENGINKO.cloud/LoRaWeb/#/configuration|LoRaWEB Tool]] (iot.ENGINKO.cloud/LoRaWeb)
Line 434: Line 436:
 ===== 11 Declaration of conformity ===== ===== 11 Declaration of conformity =====
  
-Hereby, enginko Srl declares that EGK-LW22CCM complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.+Declarations of conformity are available from Angel4Future by sending a request email to sensors@enginko.com. 
  
 ===== 12 Contacts ===== ===== 12 Contacts =====
Last modified: 2025/02/28 09:07